Skip to content

EVCC Versions

Hardware

Currently supported hardware are for ADM-CS-EVCC units of "Gen3" variant (using Vertexcom PLC chipset and Toradex Colibri iMX7 SoM). This generation had 4 hardware revisions so far.

Past hardware variants (no longer supported) were based firstly on the versatile ADM-CO-CUI1 unit, then on the first version of the ADM-CO-EVCC unit, both being "Gen2" variants (ie. using Qualcomm PLC chipset and Toradex Colibri iMX6 SoM).

Software

Releases

To install a release, follow Install a release on the Updating the Software page.

Branch Date Notable differences Download
release 2.9.0 2026-09-04
  • pev-controller 2.8.1
    • Temperature monitoring: the cable temperature function is now the default, with derating, stop and monitoring enabled by default
    • Inlet lock timing: a custom lock timing can now be configured by setting enable_custom_lock_timing to True and the delay after the charger is detected via inlet_lock_delay_s (default 5 s, range 3–60). Whatever the value, the plug is always locked at the latest just before the insulation test
    • ISO15118-20 energy requests handling: when the BMS does not provide a value, the configured energy values are used as a fallback instead of sending zeros, and the maximum request is capped by the configured battery energy capacity
    • Current deviation detection now also runs in dynamic mode against the current range
    • Generic CAN interface V1 & V2: CAN IDs can now be remapped from the configuration file
    • Plugged-in signalling: a single wake pulse is emitted when the new plugged_in_pulse_ms hardware config entry is set on a digital output
    • Diagnostic messages are no longer sent while the controller is in the Emergency state until it settles
    • Waking from sleep no longer reports a spurious node disconnection: required nodes are given a short grace period to reconnect before a NODE DISCONNECTED error is raised, instead of reacting to the stale pre-sleep heartbeat
  • ccs-evcc 2.8.2
    • ISO15118-20 fix MessageHeader timestamps: the charger clock offset is now anchored once on SessionSetupRes, instead of being recomputed from every response
    • ISO 15118-2: the optional ChargingProfileEntryMaxNumberOfPhasesInUse element is no longer sent in PowerDelivery
    • Fix a 0 Wh energy request being treated as "not provided", which broke the required min ≤ target ≤ max ordering
    • Use both Target Voltage and Target Current in Scheduled Mode by default
    • Control Pilot state reporting: state A is now reported as soon as the pistol is unplugged
    • Waking from sleep no longer reports a spurious node disconnection (see above)
    • Fixed an issue with certificate management that could prevent the vehicle from transmitting a certificate
  • slac-pev 2.4.0rc2
    • Fix: prevent double CM_ATTEN_CHAR.IND when MNBC timeout and last sound arrive concurrently
    • Waking from sleep no longer reports a spurious node disconnection (see above)
    • Unknown SLAC message types are logged at debug level instead of info, cutting down the log noise
  • advantics-csm 1.8.0
    • Configuration file: every entry now carries a description and belongs to a category, so the generated .cfg file and the web interface document themselves
    • Include the new config entries
Download link: evcc-release-2.9.0.zip
release 2.8.0 2026-06-26
  • pev-controller 2.7.0
    • ISO15118-20: cap energy requests based on config params
    • Always report the state of the digital inputs over CAN bus regardless of their configuration
    • Add possibility to use different CAN bus interfaces for IVT and Generic CAN interface using can_sensor_if config entry
    • Retry IVT sensor configuration until it powers up after init/sleep. Capped by configured timeout ivt_init_timeout_s
    • Add possibility to assert HV hold-off until the BMS reports ready using config entry hold_off_until_bms_ready
    • Enable current derate function based on temperature
  • pev-slac 2.4.0
    • fix: In multi-EVSE, duplicate CM_SLAC_MATCH.CNF lingers in buffer causing cm_set_key to hard-fail
  • advantics-csm 1.7.6
    • TLS certificates management
    • New configuration entries added
Download link: evcc-release-2.8.0.zip
release 2.7.3 2026-06-05
  • advantics-csm 1.7.4
    • Fix docker client issue that was leading to blocking behavior on image discovery
Download link: evcc-release-2.7.3.zip
release 2.7.2.post1 2026-06-01
  • Fix system services update
Download link: evcc-release-2.7.2.post1.zip
release 2.7.2 2026-04-30
  • advantics-csm 1.7.3
    • Fix configuration issue with J1939 interface
Download link: evcc-release-2.7.2.zip
release 2.7.1 2026-04-23
  • pev-controller 2.6.2
    • Introduce a configurable median filter for the lock feedback
    • Fixed reading HW variant from EEPROM
    • Bidirectional power transfer: more adapted contactors handling
    • Fixed race condition during AC ending charge affecting lock state check
  • ccs-evcc 2.7.0
    • Improved MCS sequence: wait for contactors to open at the end of ending charge phase and before setting CE state B
  • advantics-csm 1.7.2
    • Add the new config parameters
    • Add dig_out options in the UI
Download link: evcc-release-2.7.1.zip
release 2.6.1 2026-04-14
  • ccs-evcc 2.6.1
    • Fixed EVCC ID not read correctly from config file
Download link: evcc-release-2.6.1.zip
release 2.6 2026-04-10
  • pev-controller 2.5.0
    • Fixed onefile mode folders not getting cleared properly on power cycle
    • Added advanced E-stop contactor handling options for unreliable current measurements
  • ccs-evcc 2.6.0
    • Fixed onefile mode folders not getting cleared properly on power cycle
  • advantics-csm 1.7.1
    • Fix temperature config section
    • Bring back controller type to header
    • Add CSM version on footer
    • Migrate from remix to react router 7
Download link: evcc-release-2.6.zip
release 2.5 2026-03-13
  • pev-controller 2.4.0
    • Fixed checking DC contactors state and DC messages during emergency while AC charging
    • Fixed inputs message being sent with wrong values before initialization completes (startup race condition)
    • Contactors opening: raised the current-below-limit threshold to 5 A; added a configurable timeout after which contactors open unconditionally if current doesn't drop below limit
    • Startup safety: inputs messages are now suppressed until hardware I/O initialization is fully complete
    • Temperature: median filter is now applied to temperature sensor inputs
    • GC performance: persistent objects are now untracked from the garbage collector to reduce GC overhead
  • ccs-evcc 2.5.0
    • Fixed bug where frontend did not send Closing_Communication stage to backend in EmergencyShutdownState
    • Moved CP state reporting to the PLC reading level to eliminate wrong-state reports
    • Fixed alarm cancelled more than once on protocol reset (cancel only once per exit)
    • bcb_toggle_detected called from unexpected states now handled gracefully (no-op)
    • Skip CP filtering while resuming a paused session, to correctly detect the B1→B2 transition
    • Allow session resume only when the previous session is fully over
  • advantics-csm 1.7.0
    • Fix logic while exporting logs, server would respond with error code and nothing attached
    • Add the ability to generate sample config for every controller
    • Fix dynamic voltage meter bar in monitoring and use kW for power metering instead of W
    • Remove unused items from navigation side bar
    • Minor improvements
Download link: evcc-release-2.5.zip
release 2.4.1 2025-12-23
  • ccs-evcc 2.4.1
    • Bug fix: checking for wrong CP state in session stop state resulting in abnormal session termination in some cases
  • advantics-csm 1.6.4
    • fix a minor bug
Download link: evcc-23-12-2025.zip
release 2.4 2025-12-11
  • pev-controller 2.3.0
    • Add possibility of dynamic target voltage control (configurable)
    • Allow bidirectional cycling at full SOC (configurable)
    • Disable current deviation check against target current in range mode (dynamic mode)
  • ccs-evcc 2.4.0
    • Possibility to disable AC charging (configurable) (only relevant for CCS)
    • Pause and resume session according to ISO15118-2 and ISO15118-20
  • advantics-csm 1.6.3
    • Add the possibility to restart CSM when submitting config from the UI
    • Toggle J1939/CAN monitoring on config change without restarting the whole app
    • Support both extendend and non-extended IDs for CAN monitoring
Download link: evcc-11-12-2025.zip
release 2.3 2025-09-15
  • pev-controller 2.2.5
    New CAN bus message EVCC_MEVC_Diagnostic_Status: Diagnostic status of the charge controller:
    • Shows active faults and errors detected by the charge controller.
    • Status signals received from the charger over High-Level Communication (HLC).
  • ccs-evcc 2.3.5
    • Send HLC error codes and forward charger status signals received over High-Level Communication (HLC).
    • Fix minor bug in ServiceDiscovery in handling extra services.
  • advantics-csm 1.5.4
    • Fix log exporting issue; improve logging page experience (docker socket starvation, app status in colors).
    • Add export config file in config page.
    • Add J1939 capabilities; QOL improvements for J1939 logging.
    • Fix management page for EVCC (official support of EVCC).
    • Add error stack to monitoring page.
    • Fix UI typos and descriptions.
Download link: evcc-15-09-2025.zip
release 2.2 2025-08-04
  • pev-controller 2.2.4
    • New CAN bus signal HV_Preparing_Hold_Off:
      Allow the vehicle to delay the transition to powered states (starting from the insulation test) until the HV system is ready.
    • Advantics_Generic_PEV_protocol_v2: Expand energy limits and revise signal slopes accordingly.
  • ccs-evcc 2.3.3
    • Allow the vehicle to delay the transition to powered states (starting from the insulation test) until the HV system is ready.
Download link: evcc-04-08-2025.zip
release 2.1 2025-07-23
  • pev-controller 2.2.3
    • fix PEV temperature: add support for temperature monitoring
    • allow contactor feedback via CAN bus while contactor control is done via IOs
    • allow LEDs control via CAN bus interface
  • advantics-csm 1.4.2
    • extend config interface
    • fix bug in SW update process on management interface.
Download link: evcc-23-07-2025.zip
release 2.0 2025-07-07
  • New Application:
    • advantics-csm: Advantics CSM, short for Advantics Controller System Manager, handles all system-level operations.
      It provides a web interface for monitoring and configuring the system, minimizing the need for manual config file edits and command-line interactions.
      Users can access logs, manage applications, and perform system updates directly through the interface (CSM Web UI).
  • pev-controller 2.2.2
    • fix for re-entering emergency state when no_inlet_lock and contactors open CAN message not fast enough
  • ccs-evcc 2.3.2
    • Plug and Charge support
    • Fix calling GC by reset_cache causing nodes disconnection (which also asserts interlock).
Download link: pev-release-2.0.zip
Release 2024-10-15 2024-10-15 ISO15118-20 BPT: Use CAN message to dynamically update current limits pev-2024-10-15.tar
Bidirectional dev 2022-11-17 ISO 15118-20
Generic CAN interface v2
Snapshot
release 1.0 2022-11-25 Changelog -
2.0.0rc3 2022-11-03 Prefigure rc3 Snapshot
2.0.0rc2 2021-06-11 Changelog ADM-CS-EVCC (Gen3)
2.0.0rc1 2021-02-04 Changelog ADM-CS-EVCC (Gen3)
2019-06-11--001 2019-06-11 Changelog ADM-CS-EVCC (Gen2)
ADM-CO-CUI1
2018-09-25--001 2018-09-25 ADM-CO-CUI1 -